I’m not fibbing. See, it’s even in a comic strip, so it must be true.

With the van completely empty and looking shabby, I really needed to get on and finish the job. The interior was mostly done (well, the new doors I cut out needed routing – so that I can put trim around the edge – and hinges, catches etc) but while the van was empty I decided to give it a make-over (see previous post for the list).

The hardest job was putting new windows in (or old windows with new rubbers). I really needed a swear box, especially when the helpful leverage supplied by screwdriver slipped and scratched the freshly tinted windows! This was not an easy job, and I am not looking forward to doing it again. Ever.

Here’s a bit of the progress from that part of the refurb, done over 12 hours:

On the Saturday just gone, I finally put the refurbed interior back in. It was a bit of a jigsaw, and I discovered that I was missing one piece (thankfully, not a crucial part, and one I can make up out of MDF quite easily). There are still some final bits of work needed – some trimming, floor, and a few other odds and sods, but basically the donkeywork is all done now. And here’s the (almost) finished result:

Well, the restoration on the units has been going pretty good. It took a couple of weeks of filling, sanding, re-fixing old joins and applying finishing touches (fablon vinyl covering and edge trimming), along with a bit of painting, varnishing and good old-fashioned cleaning. The bed/seat is recovered and everything is almost ready to go back in, although I still have to finish the cupboard doors – just waiting on finding the right router part so I can cut a groove in the doors for the trim to go in. You can see the progress in the photos below:

Now, it just needs somewhere to go, right? This weekend I bravely took to the existing interior. Once I’d pulled up the first bit of laminate floor, well, I was committed to it then. Over the next hour and a half or so, I unscrewed and pulled out the various fittings until the back of the bus was completely empty. It looks positively cavernous in there now!

Before the refurbed interior goes back in I’m going to get a few jobs done on the inside, namely:

• Wire brush all the floor and re-paint with a black rust-proof paint
• Sand all the bodywork above the suage line on the interior from the bulkhead back
• Remove the windows with the knackered seals, also replace the pop-out windows for new (non-leaky) windows
• While the windows are out, re-tint them all – easier to do on a flat surface, and can actually put the rubbers over the top of the tinting, woohoo!
• Paint the interior above the suage line white
• Lift up the pop-top, blitz the inside with a range of toxic chemicals to remove damp spots and what have you!

Sounds like a lot, but nothing too troubling really. Can do it all myself, the only question is how quickly? Watch this space!

Long time no blog post. About time I did something about that and I have just the reason – a long overdue refresh of the interior of our VW Camper (aka our Ethel).

Last week I collected an old Dormobile (D 4/6) interior from a guy in Slough . Originally he wanted just £50 for the units and the fold-out bed, then it went down to £30 but when I actually collected it he had a change of heart and decided not to take anything for it. Perhaps, in removing the units, he realised just how much work would be involved to put them right.

So, for the next few weeks I’ll be cleaning and sanding the units, re-screwing all the joints (with counter-sunk screws that I’ll fill over and sand for a flat finish), covering entirely with new Fablon (sticky vinyl covering) in Beech finish, and putting new hinges on everything. The only hurdle I’m expecting, to be honest, is finding some trip to apply to the edges of the doors – I may need to improvise somewhat!

Once all the units are in good shape inside the house, I’ll take out the existing interior and start plumbing in the new ones. I’m hoping that will be the easy part.

So, I’ll update the progress on the blog, partly for my own records, and partly in the hope that someone searching for door trim for Dormobile units might chance upon this site – and if they do, please let me know where I can get some!